SCS 770724

724 Plus Workstation Monitor

In Stock ESD-Safe

The SCS 724 Plus Workstation Monitor continuously monitors the path-to-ground integrity and body voltage of two operators, as well as the path-to-ground integrity for one conductive or dissipative work surface. The 724 Plus Workstation Monitor eliminates the need for periodic testing and record-keeping of wrist straps.

Single Workstation Continuous Monitor
Continuously monitors the path-to-ground integrity of two operators and one conductive or dissipative worksurface; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
Digital Signal Processing Technology
Provides stable continuous monitoring (versus pulsed or intermittent) of the wrist strap’s path-to-ground and the presence of its 1 megohm safety resistor
Operator Body Voltage Detection
Alarms if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item
0.40 Volt Operator Test Voltage
Reduces the risk of electrical overstress (EOS) for the handling of sensitive components
500 Millisecond Alarm Response Time
Identifies failures and intermittencies that inferior technologies miss
Operator Remote Disconnect Alarm
Prevents tampering should one intentionally disconnect the operator remote from the monitor
Miniature Monitor Size (0.85 x 2.4 x 2.6 inches)
Occupies minimal space and includes mounting tabs secure installations
Dedicated Monitor Ground Cord
Allows the monitor to be bonded to a reliable ESD ground, AC equipment ground, or auxiliary ground
Use with Dual-Wire Wrist Straps
See SCS dual-wire wrist straps
Calibration Verification
Use the SCS 770734 Verification Tester to check the test limits of 724 Plus Workstation Monitors without removing them from their workstations
NIST Calibrated with Certificate Included
Calibrated with accepted procedures and standards traceable to the National Institute of Standards and Technology. For more information on the calibration of SCS products, see Calibration.
100-240VAC Power Adapter with Interchangeable Plugs
Works with standard electrical systems in North America, the United Kingdom, Japan, Asia, and Europe
Made in the United States of America

U.S. Patents 6,930,612; 9,983,251

Special Price $264.42 Regular Price $278.34

Skip to the end of the images gallery

Skip to the beginning of the images gallery

Technical Documents

Specification Sheets

SCS 724 Plus Workstation Monitor Specifications

Warranty

SCS Product Warranty

Details

The 724 Plus Workstation Monitor is designed with digital signal processing technology for true continuous monitoring (versus pulsed or intermittent) of wrist strap functionality (path-to-ground and presence of two 1-megohm resistors) and operator safety according to accepted industry standards. It is unaffected by capacitance variations from personnel or the environment. Digital signal processing technology uses dual-wire wrist straps to apply a low test voltage of 0.40 V onto the operator for the handling of sensitive components.

The 724 Plus Workstation Monitor features operator body voltage detection. It will alarm if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item. Each 724 Plus Workstation Monitor is calibrated with accepted procedures and standards traceable to the National Institute of Standards and Technology (NIST) and includes a certificate of calibration.

ANSI/ESD S20.20 section 7.3 states "Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements." Per ANSI/ESD S1.1 Annex A.3 Daily (wrist strap system) "testing may be omitted if constant monitoring used." Per ESD Handbook ESD TR 20.20 section 5.3.2.4.4 "Typical Test programs recommend that wrist straps that are used daily should be tested daily. However, if the products that are being produced are of such value that knowledge of a continuous, reliable ground is needed, and then continuous monitoring should be considered or even required."

Includes

1 724 Plus Workstation Monitor
1 Dual Operator Remote
1 Operator Remote Cable
1 Mat Monitor Cord (White)
1 Monitor Ground Cord (Green and Yellow)
1 Countersunk Washer
1 Flat Head Screw, 6-32 x 1/4"
4 Pan Head Screw, #6 x 3/8"
1 Power Adapter, 12 VDC, with interchangeable plugs (North America, UK/Asia, Europe)

Technology: Digital Signal Processing
Wrist Strap Type: Dual-Wire
Operator(s): 2
Worksurface(s): 1
Metal Ground(s): 0
Body Voltage Detection: Yes
EOS Detection: No
Contact EMI Voltage Detection: No
Relay Terminal: No
Software Compatibility: No
Operator Test Voltage (open circuit with respect to ground): 0.40V